lubrication, string ball ends stuck in mechanism, etc.) NOTE: Do NOT attempt this until you have exhausted all other possible remedies to solve problems with the ability of your steel guitar to maintain its tuning. Recheck the kne lever for the correct amount of slack in its travel.
Do this by pulling the string past the desired pitch, releasing it, and then retuning the open string.Ħ. Adjust the position of the knee lever or the linkage to allow enough travel to pull the string to the desired pitch. Type 2 knee levers feature fixed, non-adjustable stops which the knee levers engage at the end of their travel.ĥ. Re-check the knee lever for the correct amount of slack in its travel. Adjust the knee lever stop (usually a screw or adjustable assembly of some type) to allow more travel to the knee lever mounting bar before it engages the stop screw.Ħ. If the string comes back sharp (flat for lowers), it is an indication that you don't have enough travel.ĥ. If the string returns to proper pitch, you have enough travel. Release the knee lever and check the open tuning. Type 1 knee levers feature adjustable stops which the pedals engage at the end of their travel (shown above).Ĥ. To adjust the different types of knee levers, follow these steps: We recommend you familiarize yourself with the operation of the different types of knee levers as they apply to your steel guitar. Whichever system the knee levers use, they should still demonstrate a slight amount of slack in the travel before engaging the changer fingers. Note: Some guitars may use both systems, one for knee levers that move to the left and the other for knee levers that move to the right. Most pedal steel guitars use 1 of 2 different systems to adjust the knee lever slack. The slack can be observed as a small amount of movement of the pull rod or rotation of the cross shaft and pull bar when moving it (as shown above). Make sure your knee levers have a small amount of slack in the travel before they cause the tuning nuts to engage, the fingers which raise and lower the strings.
EMMONS STEEL GUITAR TUNING PEGS FREE
Travel - necessary to maintain the correct amount of slack and travel for trouble free operation (large screw shown) Tilt - useful only for comfort and alignment. Recheck the pedal for the correct amount of slack in its travel. The pedal bell crank is attached to the cross shaft and is the part into which the pedal rod hooks.Ħ. Adjust the slack adjustment screw on the pedal bell crank to allow more travel to the pedal. Type 2 pedal stops feature fixed, nonadjustable stops which the pedals engage at the end of their travel (Zum, Emmons, Derby).ĥ. Re-check the pedal for the correct amount of slack in its travel. Adjust the pedal stop (usually a screw of some type) to allow more travel to the pedal bell crank before it engages the stop screw.Ħ. If the string comes back sharp, it is an indication that you don't have enough travel.ĥ. Release the pedal and check the open tuning. The smaller the gauge, the greater the travel.Ĥ. Plain strings require more travel than wound ones.
Tune the raise (or lower) on the string that travels the farthest. Type 1 pedal stops feature adjustable stops which the pedals engage at the end of their travel (MSA, MCI, Sho-Bud, Carter, Mullen).ģ. To adjust the different types of pedals follow these steps: Whichever system the pedals use, they should still demonstrate a slight amount of slack in the travel before engaging the changer fingers. Most pedal steel guitars use 1 of 2 different systems to adjust the pedal slack. The slack can be observed as a small gap which appears between the pedal and the guitar body when moving it (as shown above).
So let's look at for example, the very first pedal that we have, the A pedal.Make sure your pedals have a small amount of slack in the travel before they cause the tuning nuts to engage, the fingers which raise and lower the strings. It's just going to make the pedal or knee lever do more of the task that you're asking it to do. So that's the thing to keep in mind is that you're not necessarily talking about raising when you're increasing. And what you have here is a little three sixteenth socket wrench that fits these little hex things and they allow you to raise or lower, or increase or decrease I should say, the amount of effect that a pedal or knee lever has on a string. Now, what this does is to affect how much effect the pedals and knee levers have on the strings in terms of raising or lowering them. You use the tuning pegs to tune the strings to the tunings that we've previously discussed and that gives you your open string tunings.
EMMONS STEEL GUITAR TUNING PEGS HOW TO
We've already discussed how to tune the strings. How do you tune the pedals? Okay, well what we have here is the tuning mechanism for the pedals and the knee levers.
0 kommentar(er)
